This is an old revision of the document!
Digital DMR Dual-Band Handheld Commercial Radio
The AnyTone D868UV radio is a VHF and UHF radio with both Digital DMR (Tier I and II) and Analog capabilities. It offers a total of 4,000 channels (Analog and Digital) and up to 130,000 contacts, as well as multiple DMR ID numbers (Radio ID’s) for a single radio.
This radio is a Part 90 DMR commercial transceiver with a 1.77-inch color TFT display. 4,000 Channels with 10,000 Talk Groups. Frequency coverage is 140-174 / 400-480 MHz.
Memory Channels | 4,000 |
DMR Talk Groups | 10,000 |
Digital Contacts | 150,000 |
Power Levels | 6/4/2.5/1 Watt transmit power levels |
Zones | 150 zones, up to 250 channels per zone |
Display | 1.77-inch color TFT Screen |
Battery | 3150 mAh lithium-ion battery |
Bandwidth | 12.5 / 25.0 kHz analog and 12.5 kHz DMR |
Import/Export | Enhanced CPS allows direct input and export of channels, digital IDs, and talkgroups. |
DMR Compatibility | Supports Tier I and Tier II operation, making it compatible with DMR repeaters that utilize two-slot TDMA technology |
Analog Compatibility | Compatible with amateur radio analog repeater and simplex use on both wide and narrowband |
Programmable | FCC 47CFR90.203 requires the keypad locked in the shipping configuration. Software keypad unlocking and re-programming are available |
CTCSS/DCS | CTCSS/DCS tone transmit and receive capable with split tone capability |
Certifications | FCC Part 90 certified, FCC ID: T4KD868UV |
The software which programs the radio frequencies and all other user-defined aspects of the radio operation is called a “code plug.” Creating a code plug is a ‘bottom-up’ process where the lowest (common) elements must be created first, then built upon until a fully functional code plug that can be loaded into a radio has been created. The AT-D868UV radio has unique software for creating the code plug and writing it into the radio for use. When you start creating a new code plug, many lists and groups are populated with single entries, which may be used as placeholders for the initial creation of lists. The programming software allows importing and exporting most of the programming parameters to create a large amount of input data to the radio (i.e., large lists of contact names).
RepeaterBook is currently developing a project to export data from DMR repeaters into a CSV file imported into the radio's CPS. The export will allow for the collection of both analog and DMR repeaters and the associated DMR talkgroups. RepeaterBook has thoughtfully considered repeater owners' concerns by not exporting configurations likely to cause harmful interference on the repeater, such as guessing at time slots for talkgroups. If a time slot is not known, the talkgroup is skipped and not exported. However, it is ultimately the radio operator's responsibility to assure that the exported data, subsequently imported to the radio via any means, is proper and correct for the repeater's desired operation.
The first searches with export capability will be linked from the DMR Niche Pages.
This is a multi-step process when working with this radio. You must first download the talk group CSV and import it to the radio. The complete CSV of all talk groups can be downloaded here.
The talkgroup CSV contains every talk group recorded in the RepeaterBook database. There are three options, based on your needs:
RepeaterBook default is BOLD.
Data Fields | Values |
---|---|
No. | |
TG/DMR ID | Numeric DMR talkgroup ID. |
Repeater Number | Full name of the talkgroup. Spaces are OK. Truncated at 9 characters. |
Name | Full name of the talkgroup. |
City | It can be blank. |
State | It can be blank. |
Country | It can be blank. |
Remarks | It can be blank. |
Call Type | Group Cal |
Call Tips | None |
Once all talkgroups are entered, the Contact List should be imported back into the programming software the same way you exported the file. Click on TOOLS and then import. In the new window, click on Digital Contacts and select the .csv file you want imported.
The next step is to fill the radio with all possible contacts you may ever encounter. By doing this, the radio will, for each contact you make, display the name, DMR ID, callsign, etc., of the individual you are connected with.
The Contact List is a “look-up” table for the radio to display all the contacted person's details instead of only the DMR ID number. Individual entries (updates) can be made as shown below but would be very time consuming when creating the initial list.
A master list of DMR contacts in CSV format is available at the DMR-MARC website: All DMR-MARC Users
This database of contacts can be directly used for DMR ID’s and imported into the radio as required. Download the list and open it up as an excel spreadsheet.
This step is completed completely outside of RepeaterBook. Follow the CPS manual for additional information.
This step is completed completely outside of RepeaterBook. Follow the CPS manual for additional information.
This step is completed completely outside of RepeaterBook. Follow the CPS manual for additional information.
This step is completed completely outside of RepeaterBook. Follow the CPS manual for additional information.
This radio offers the programming of 4,000 channels for UHF and VHF.
The following information was derived from deconstructing the exported CSV file from the radio. Each row is headered by the column name in bold below. Each contact row requires an entry in each of the columns. If certain data is unknown and could cause undesired consequences when transmitting on a repeater, such as defaulting a time slot to 1 when the time slot is not known, the contact will be skipped. Users must acknowledge that the data from RepeaterBook cannot be 100% guaranteed and must be re-checked through local sources before attempting to transmit through a repeater.
This is an auto-incremented record number starting with 1 and increases in integer steps by 1. It should either be empty or show sequential numbers starting with 1 for channel 1, 2 for channel 2, etc. RepeaterBook will auto-number each row sequentially.
The name of the channel (typically the name of repeater and talkgroup). Propose using the name of the nearest city and a talk group alias (abbreviation).
The receive frequency on the radio. Format is “nnn.nnnn”.
The transmit frequency on the radio. Format is “nnn.nnnn”.
Enumerated Values: “A-Analog,” “D-Digital.”
For DMR channels, use D-Digital. For Analog channels, use A-Analog. Mixed analog and mixed digital are also available. Still, more information is needed as to the value to be entered into the output and the purpose for each setting (conditions the export program to follow to set the mode).
Transmit power setting for this channel. Enumerated Values: “High”, “Low”
The radio is capable of four output power settings. Is there a “mid1”, “mid2” or equivalent setting? RepeaterBook will set this to “Low” to comply with FCC rules regarding utilizing the lowest transmit power required to maintain reliable communications. Users can override this setting in the export as needed.
Bandwidth of the emission. Enumerated Values: “12.5K”, “25K”
Use “12.5K” for DMR and “25K” for analog. When RepeaterBook begins tracking the bandwidth of the supported repeater modes, use this value instead.
Values: “Off”, analog PL value, digital PL value. Digital PL example “D125N”. Analog PL example “82.5”. Use the appropriate code or set it to “Off” if no code or “CSQ” is present.
Values: “Off”, analog PL value, digital PL value.
Digital PL example “D125N”. Analog PL example “82.5”. Use the appropriate code or set it to “Off” if no code or “CSQ” is present.
Digital only. Name of the DMR talk group. It is allowed to have spaces. Maximum characters? For analog repeaters, it appears as though the name is “Contact 1”.
Digital only. This is the call sign of the radio owner. Since RepeaterBook requires users to be logged on to export, it will pull the logged-on user's call sign and insert it into this field.
Enumerated Values: “Always,” “Same Color Code,” “Off”
The CPS Manual suggests using “Same Color Code” as the typical setting. More information is needed regarding this setting, and the conditions the export program should follow.
Enumerated Values: “Carrier”, “CTCSS/DCS”
This is the receive tone squelch (TSQ). It only applies to analog repeaters. If a repeater is known to be transmitting a CTCSS/PL/DPL tone, then turn this field to “CTCSS/DCS.” If the repeater is DMR, then set to “Carrier.”
Enumerated Values: “Off”, “DTMF”, “2Tone”, “5Tone”.
RepeaterBook will set to “Off.”
Values: ?
Analog only. DTMF ID. RepeaterBook will set to “1”.
Values: ?
Analog only. 2 Tone ID. RepeaterBook will set to “1”.
Values: ?
Analog only. 5 Tone ID. RepeaterBook will set to “1”.
Enumerated Values: “Off”, “at start”, “at end”, “both”.
Analog channel only. RepeaterBook will set to “Off.”
Enumerated Values: “0”, “1”, “2”, “3”, “4”, “5”, “6”, “7”, “8”, “9”.
Digital channel only. The color code is needed to access the repeater. RepeaterBook will enter the color code associated with the repeater. If no color code is known, the value will be set to “0”.
Enumerated Values: “1”, “2”.
Digital channel only. The time slot the talkgroup (contact) is assigned to on the repeater. RepeaterBook will set the time slot listed for the talkgroup in our database. If the time slot is not known, the talkgroup will be skipped from export.
The scan list the channel belongs to. Possible Values: “None,” name of the list.
Export will set to “None” and require the user to update the data as needed.
Values:
Digital channel only. RepeaterBook defaults to “None.”
Prevent the radio from transmitting on the channel (listen-only). Enumerated Values: “Off,” “On”
Set to “Off” will allow transmitting on the channel. Set to “On,” and the PTT will be locked out on this channel. Export will set all channels to “Off” since the database only contains channels located on the amateur radio plan.
Enumerated Values: “Off,” “On”
Export will set this to “Off.”
Enumerated Values: “Off,” “On”
Digital channel only. Export will set to “Off.”
Enumerated Values: “Off,” “On”
Digital channel only. Export will default to “Off.”
Enumerated Values: “Enhanced Encryption”, “Normal Encryption”.
Digital channel only. Export will set to “Normal Encryption.”
Enumerated Values: “Off,” “On”
Digital channel only. Export will set to “Off.”
Enumerated Values: “Off,” “On”
Digital channel only: Export will set to “Off.”
Enumerated Values: “Off,” “On.”
This sets the transmit frequency to the receive frequency, putting the radio in simplex and transmitting on the repeater's output frequency.
Enumerated Values: “Off,” “On.”
This is allowing an emergency button for workers who are alone to use. Export will default this to “Off.” RepeaterBook will set this to “Off.”
Analog channel only. Can use a custom-entered frequency (Hz). RepeaterBook will set this to “0”.
This step is completed completely outside of RepeaterBook. Follow the CPS manual for additional information.