This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
adms-12 [2020/12/01 13:37] kd6kpc |
adms-12 [2023/04/26 13:13] kd6kpc [Limitations] |
||
---|---|---|---|
Line 2: | Line 2: | ||
* [[https:// | * [[https:// | ||
+ | |||
+ | The Yaesu ADMS-12 software is specifically for programming the [[ftm-300|Yaesu FTM-300DR]] radio. Also, the transceiver parameters and the setup menu items may be edited and configured. | ||
+ | |||
+ | The radio is shipped with a micro-USB cable. This cable is NOT for programming the radio. It is only for performing firmware updates. The cloning cable is the SCU-20 which must be purchased separately. | ||
+ | |||
+ | An alternative method for programming the radio is with a microSD card. A microSD card is not included with the radio but can be purchased separately. | ||
+ | |||
+ | {{url> | ||
+ | |||
+ | RepeaterBook recommends a microSD card no larger than 32 GB. The radio is not capable of reading larger cards. The card featured above has been tested in two separate FTM-300DRs and has worked perfectly. | ||
+ | |||
+ | ===== Importing / Exporting ===== | ||
+ | |||
+ | The software can import and export in the following formats: | ||
+ | |||
+ | * CSV | ||
+ | * FTM100D/ | ||
+ | * FT2D format | ||
+ | * FT3D format | ||
+ | |||
+ | |||
+ | This version of the ADMS software is supported by RepeaterBook. A full list of the supported searches can be found [[adms-12# | ||
+ | |||
+ | The FTM-300DR supports 999 memory channels. | ||
+ | |||
+ | ===== Supported Searches ===== | ||
+ | |||
+ | ^ Search Page ^ North America | ||
+ | | **Favorite** | ||
+ | | **Feature** | ||
+ | | **Keyword** | ||
+ | | **Location** | ||
+ | | **Multi-County** | ||
+ | | **Multi-State** | ||
+ | | **Proximity** | ||
+ | | **Proximity 2.0** | <color green> | ||
+ | | **Quick** | ||
+ | | **Travel** | ||
+ | |||
+ | ===== CSV Format ===== | ||
+ | |||
+ | There are no header field names in the file. RepeaterBook defaults are **BOLD**. | ||
+ | |||
+ | ^Field Name ^ Field Value| | ||
+ | |Channel No | Sequential beginning with 1 | | ||
+ | |Receive Frequency|| | ||
+ | |Offset Frequency| Shift in MHz| | ||
+ | |Offset Direction| -RPT, +RPT, -/+, OFF| | ||
+ | |Operating Mode| AM, **FM**| | ||
+ | |DIG/ | ||
+ | |Name|| | ||
+ | |Tone Mode| OFF, TONE, TONE SQL, DCS, REV TONE, PR FREQ, PAGER| | ||
+ | |CTCSS Frequency| Repeater uplink tone or **88.5**| | ||
+ | |DCS Code| Repeater uplink DCS Code or **023**| | ||
+ | |User CTCSS| **1600 Hz** | | ||
+ | |RX DG-ID| Downlink DG-ID or **RX 00**| | ||
+ | |TX DG-ID| Uplink DG-ID or **TX 00**| | ||
+ | |TX Power| **HIGH**, MID, LOW| | ||
+ | |M-GRP| **OFF**| | ||
+ | |SCAN| **YES**, NO| | ||
+ | |Step| **5.0KHz**| | ||
+ | |Narrow|**OFF**| | ||
+ | |Clock Shift|**OFF**| | ||
+ | |Comment|| | ||
+ | |||
+ | ===== Limitations ===== | ||
+ | |||
+ | The RepeaterBook export automatically filters unsupported frequencies and digital modes. | ||
+ | |||
+ | The frequencies exported are between 100 MHz and 1000 Mhz. | ||
+ |